Baxi Fires Division 740FS Manuel d'utilisateur

5115978/02© Baxi Heating U.K. Limited 2007.Model 740FSInset live fuel effect gas fireIncorporating the BAXI FIRES DIVISION CONTROLFitted with one of t

BS1289 and BS EN 1858recommend that there should bean air space or insulationbetween the flue blocks and theplaster because heat transfer maycause cra

to the top of the chimney. An approved terminal must be fitted.! A properly constructed precast concrete or clay flue system conforming to BS1289or BS

3.11 Adorn model onlyThe minimum height from the base of the fireplace opening to the underside of anyshelf made from wood or other combustible materi

Page 13INSTALLER GUIDE© Baxi Heating U.K. Limited 2007.3.12 Note that soft wall coverings (e.g. embossed vinyl, etc.) are easily affected byheat. They

Page 14INSTALLER GUIDE© Baxi Heating U.K. Limited 2007.3.20 Proprietary terminals must comply with BS 715 or BS 1289. Any terminal ortermination must

Page 15INSTALLER GUIDE© Baxi Heating U.K. Limited 2007.Figure 5 continued. Appliance dimensions and clearancesKey DescriptionModelAdorn Visage Icon D

4. PACK CONTENTSThe items required for this appliance are packed in sections.Section 1 - Fire unit contains:1 Burner and convection box unit.1 Nut and

Page 17INSTALLER GUIDE© Baxi Heating U.K. Limited 2007.Figure 6. Pack contents

Page 18INSTALLER GUIDE© Baxi Heating U.K. Limited 2007.Figure 6. Pack contents continuedETERNALDECADENT

Carefully remove all the contents. Take special care in handling the ceramic pieces.Take care not to bend or distort the slide control linkage when ha

© Baxi Heating U.K. Limited 2007.All rights reserved. No part of this publication may be reproduced in any material form(including photocopying), stor

5. FIREPLACE CHECK5.1 Fireplace check.5.1.1 Fireplace size.The fireplace must complywith the requirementsdescribed in section 3.2.This will probably e

fireplace floor are sound enough to take the eyebolts and screws. If these areas havedeteriorated due to prolonged use, they should be made sound with

7. GAS SUPPLY CONNECTIONA nut and olive are provided for an 8mm pipe inlet connection to the ‘T’ connector atthe bottom front of the appliance. The ‘T

unless the supply pipe is to pass through it.5. The appliance is supplied with two fireback spacers. Donot fit the fireback spacers if the fire is to

8. This appliance is supplied with a rear ceramicsupport bracket. Fit this using two screwssupplied (See figure 15)9.This appliance is supplied with a

9. CONVECTION BOX INSTALLATION9.1 Method 1 - Front fixing to fireplace surround.1. Make sure that the fireplace front surround area is sound enough to

masonry drill. The holes shouldbe equidistant each side of thecentre line of the fireplace toensure that the appliance finishescentrally in the openin

6. Thread the cables through the eyebolts. Return the cablesthrough the holes near the bottom of the convection boxback panel (See figure 22) (For pre

box is aligned squarely and the sealing is satisfactory, fully tighten the cable retainers.13. If the convection box is not correctly aligned, release

(See figure 26). This should close the ignition circuit and simultaneously open the gastap allowing the gas to flow to the pilot. Wait a few seconds w

Page 3INSTALLER GUIDESafety First.Baxi Fires Division fires are CE Approved and designed to meet the appropriate BritishStandards and Safety Marks.Qua

11. CERAMIC WALLS INSTALLATION1. Fit the ceramic rear wall inside the “L” bracket on the back face of the burnercompartment. Push the ceramic wallflat

12. FASCIA AND CONTROL LINKAGE12.1 Remove the tape securing the control linking barto the fascia. Slide the control button upwards as faras it will go

convection box. Lower the fascia unit makingsure that the retaining plates locate fully overthe brackets on the convection box (See figure32).Swing th

Fit the burner baffle to the front flanges ofthe burner. To do this, place the baffleagainst the front flanges of the burner andlower into position. T

13. FITTING THE CERAMIC FUEL EFFECTThe installer and owner guide for the ceramic fuel effect is supplied with the ceramicfuel effect. It is important

14.4 “Dream” fascia.14.4.1. Place the firefront casting centrally on topof the hearth in front of the fascia.14.4.2. Place the bottom front cover cast

15. FULL OPERATING CHECKS15.1 Checking the control settings.The control position markings on the fascia are shown in figure 44.Please note:! When fir

4. The smoke match should be placed horizontally into the convection box at the righthand side. There is a notch in the black cross member. Insert the

This monitoring system, or any of its parts, must only be exchanged usingauthorised parts.3. Open the isolating valve on the inlet ‘T’ connector. Scre

17. SERVICING & PARTS REPLACEMENT! Always turn off the gas supply before commencing any servicing (Theappliance inlet ‘T’ connector incorporates

Page 4INSTALLER GUIDE© Baxi Heating U.K. Limited 2007.CONTENTSSection Heading Page1. SAFETY 52. APPLIANCE DATA 63. GENERAL INSTALLATION REQUIREMENTS

17.1 Checking the aeration setting of theburner.1. The aeration shutter is factory set for usewith a ‘pebble’ ceramic fuel effect. It isimportant to e

3.Loosen the thermocouple nut to free the microswitch leads and pull the leads clear ofthe thermocouple interrupter block (See figure49).4. Detach the

4. Make sure that the control linking bar has beendetached (See 2 above). Carefully lift the fasciaupward to clear the upper retaining brackets on the

Visage model1. Remove the fascia (See section 17.4).2. Detach the rear baffle3.Detach the slide unit by removing two screws securing the plastic slide

55).5. Replace in the reverse order.17.8 To remove the electronic ignitiongenerator.1. Remove the bottom front and fire frontcastings. For ‘Adorn’ and

that the leads are secured in the interrupter block to give a good electrical contact.17.10 To remove the pilot unit.1. Remove the burner unit (See se

When refitting the thermocouple and interrupter block, make sure that the microswitchwires are properly secured to give a good electrical contact.17.1

17.14 To remove the main burner injector.(See figure 61).1. Remove the burner (See section 17.13).2. Remove the burner clamping screw (See figure 61)3

1. SAFETYInstallerBefore continuing any further with the installation of this appliance please read thefollowing guide to manual handling! The lifting

2. APPLIANCE DATA*When converted using kit 0595211.The appliance data label is located on a plate at the base of the fire. This can be seen bylowering

This product uses fuel effect pieces and burner compartment walls containingRefractory Ceramic Fibres (RCF), which are man-made vitreous silicate fibr

BS 5440 Part 2BS 6461 Part 1BS 1251BS EN 1806BS 5871 Part 2BS 6891BS 8303In England and Wales, the current edition of the Building Regulations issued

2.1.1 ‘Hole-in-the-wall’ Installations! It is recommended that a hearth should be installed as in section 3.9. ! Icon firefront If when using the Ico